Graphene additive dispersion in a laboratory beaker on a black background

Graphene Integrations shop

Graphene Products

Pre-mixed graphene additives, ThermaGraph™ coolants and graphene dispersions for oils, cooling loops, concrete, polymers and coatings. Patent pending and made in the USA.

Graphene Integrations makes graphene additives for lubricants, concrete, polymers, coatings and batteries, ThermaGraph™ coolants for data center and HVAC cooling loops, and graphene dispersions for your own formulations. Everything is supplied pre-mixed in a carrier matched to its application, never as a loose powder, so it goes straight into your process. Browse by category below, or request a quote and we will size the order and send a technical data sheet.

  • Pre-mixedSupplied in a carrier, never as powder
  • Patent pendingProprietary integration process
  • Made in the USAManufactured in Charlotte, NC
  • Quote-basedSized to your volume, TDS and SDS on request

Shop by category

ThermaGraph™ ready-to-use graphene coolants for closed cooling loops: ThermaGraph™ in deionized water for data center water loops and closed-loop HVAC, and ThermaGraph-D™ in white mineral oil for single-phase immersion. Patent pending.

From heat-transfer performance to an efficient cooling loop

ThermaGraph™ is a complete water-based fill for suitable closed loops, with 0.5–1.5 wt% graphene in the supplied fluid—not a top-off dose. GI’s +6–18% higher convective heat-transfer coefficient versus a glycol baseline comes from internal pumped-loop tests. It is not independent field validation or an equivalent percentage electricity saving.

DOE’s liquid-cooling evaluation illustrates system-level metering; it did not test GI fluid. Assess environmental outcomes using measured kWh, the actual electricity mix, fluid manufacture, replacement, transport and disposal. Improved heat transfer is an opportunity to optimize the system, not a measured GI carbon footprint.

Research / measurement reference · Continue with the application guide

Graphene additives you blend into motor oil, gear oil, hydraulic fluid, grease and coolant, each pre-mixed in a carrier matched to the fluid.

Translate bench protection into a formulation trial

GI’s lubricant additives use graphene integrated into oleic acid and monomer. The 1–7% by-weight treat-rate guidance concerns the supplied additive; agree the dosing basis and carrier for your formulation rather than treating it as neat-graphene content.

Compare the finished formulation with its own baseline: viscosity, additive-package compatibility, oxidation, filtration and the relevant wear/load tests. For grease, also check thickener compatibility and consistency; for hydraulics, check air release and pump behavior. Demonstrate any resource benefit with actual oil consumption, replacement parts, drain intervals and energy under matched duty, including additive production and end-of-life in the environmental balance.

Research / measurement reference · Continue with the application guide

Graphene for concrete and reinforcement: a pre-mixed concrete additive dosed by weight of cement, and graphene rebar, which is in development.

Concrete strength and embodied carbon

Cement is the binder in concrete. Its production releases CO₂ through limestone conversion and energy use, as explained by the IEA. That makes cement quantity an important part of a concrete carbon assessment.

GI’s additive achieved +67.7% compressive strength in third-party testing at the tested 5% supplied-additive dose by cement weight, not 5% pure graphene. This validated strength result supports investigating lower-cement mixes; it does not establish how much cement can be removed. Candidate mixes must meet the same required performance.

Conditional example: if 100 kg of Portland cement is actually avoided at the same required performance, gross avoided cement A1–A3 impact is 100 × 0.919 = 91.9 kg CO₂e. The 100 kg is an example assumption, not a reduction demonstrated by GI. The official US industry-average Portland cement EPD, revised July 2026, Table 4, gives 0.919 kg CO₂e/kg using 2019 production data, covering A1–A3, raw materials through manufacturing—not a current-year plant measurement or whole-life concrete footprint. CO₂e means carbon dioxide equivalent.

This is gross avoided cement-production impact, not measured GI net savings. Net savings require matched-performance mix validation and a consistent lifecycle comparison including additive manufacture, carrier, packaging, transport and all changed mix inputs. Unknown additive impacts are not zero. The strength result does not automatically establish cement reduction, longer service life or carbon capture.

Explore the concrete and embodied-carbon guide.

Graphene additives for paints, coatings, adhesives and sealants, supplied as a liquid you mix into your formulation.

Evaluate the joint, not just the additive

Graphene can be investigated for stress transfer and thermal or electrical pathways in polymer systems. Published epoxy research highlights the importance of the filler–matrix interface; its modified graphitic materials and results are not specifications for GI adhesive formulations.

A resource-efficient joint must deliver the required function over its service duty. Record actual adhesive use, process scrap, cure energy, repair needs and disassembly or recycling constraints. Include additive and carrier impacts in any lifecycle comparison; a stronger coupon alone does not establish longer field life or a CO₂ reduction.

Research / measurement reference · Continue with the application guide

Graphene additives for plastics, rubber, 3D printing filament and textiles, added during compounding, mixing or finishing.

Match material performance before claiming material efficiency

Graphene offers a route to investigate reinforcement and thermal or electrical networks in a polymer. Primary epoxy research shows how matrix interaction and filler structure affect performance; different grades, polymers and processing cannot be assumed to reproduce those results.

Potential material efficiency requires a design that meets the same requirements—not simply a stronger coupon. Track accepted-part mass, production yield, processing energy and repair or replacement, then include additive, carrier, transport and end-of-life. Improved material properties alone do not establish lightweighting, recyclability or a measured GI carbon saving.

Research / measurement reference · Continue with the application guide

Graphene additive for battery electrode slurries, for research and development teams testing conductivity in their own cells.

Evaluate the electrode before the battery claim

Graphene is investigated as a conductive network within an electrode, not as a replacement for all its active chemistry. Published cathode research links a specific graphene coating architecture to electron and ion transport; that electrode design and its performance are not GI additive results.

Potential resource benefits must follow a cell that meets the same duty and safety requirements. Compare delivered energy over demonstrated service, manufacturing yield, drying energy, electrolyte and other materials, transport and end-of-life. Faster charging or better conductivity alone does not demonstrate a longer-lived or lower-carbon GI battery.

Research / measurement reference · Continue with the application guide

Graphene pre-dispersed in water, solvents, resins, oils or the carrier your process needs, for teams that build their own formulations. Quote only: we confirm the carrier for your application before an order.

Choose the carrier around the manufacturing task

A dispersion is a delivery form: its carrier must fit the water, solvent, resin or oil system it enters. GI uses exfoliation and a proprietary suspension process; supplying graphene in liquid does not make different carriers interchangeable. Confirm the selected formulation’s SDS and TDS before use.

A practical resource assessment records accepted production output, mixing and drying energy, carrier losses, transport, cleaning, waste and end-of-life. Stable processing or fewer rejects may help, but demonstrate that improvement in the actual process and include graphene/carrier manufacture. A water-based or pre-dispersed label alone does not establish non-toxicity or a lower-carbon footprint.

Research / measurement reference · Continue with the application guide

Graphene additive production line at Graphene Integrations

Not sure which additive fits?

Tell us your base material and target property. We will recommend an additive and a starting dose, and send samples for testing.