ThermaGraph-D™ Immersion Cooling Fluid
A graphene-enhanced dielectric fluid in white mineral oil for single-phase immersion cooling of data center servers.
- Category
- Data Center & HVAC Coolants
- Application
- Single-phase immersion tanks for data center, HPC and edge servers, where the boards sit directly in the fluid.
- Carrier
- white mineral oil (CAS 8042-47-5), grade stated on the certificate of analysis.
- Use
- Ready to use as an immersion fill. Graphene loading 0.05–0.20 wt%, stated on the certificate of analysis.
- SKU
- GI-TGD-5GAL (5 gal pail)
GI-TGD-55GAL (55 gal drum)
GI-TGD-275GAL (275 gal tote)
Sizes: 5 gal pail, 55 gal drum, 275 gal tote
Request a quote for pricing, lead time and the right dose for your job.
Downloads
Patent pending. Made in the USA. Manufacturer: Graphene Integrations, Charlotte, NC.
About this product
ThermaGraph-D™ is graphene pre-dispersed in white mineral oil, formulated as a dielectric fluid for single-phase immersion cooling, where servers sit directly in the fluid. It is supplied pre-mixed, never as powder, and contains no carbon black.
Electrical and thermal
Formulated for low electrical conductivity and enhanced thermal conductivity. Electrical suitability must be verified for the supplied lot and the intended equipment before energizing electronics. Measured values, including breakdown voltage, are reported on each lot’s Certificate of Analysis.
If it leaks
Glycol-free, mineral oil base. Do not swallow: aspiration hazard (Category 1, H304: may be fatal if swallowed and enters airways); do not induce vomiting. Prolonged skin contact may cause dryness (see SDS). Isolate power, absorb and clean before re-energizing.
Breakdown voltage and electrical conductivity are reported on the signed technical data sheet for each lot, and heat transfer is reported against the unfilled dielectric at the same temperature and method. Do not energize boards until those electrical values are on the signed sheet.
ThermaGraph-D™ is a data center product. It is not for two-phase systems and not for water or glycol loops; for closed water loops, including HVAC, see ThermaGraph™. We recommend a 30-day sample in your tank with corrosion and material coupons before a full fill.
Available in 5 gal pails, 55 gal drums and 275 gal totes. Pricing is by quote while online pricing is prepared.
Evaluate immersion as a complete fluid system
ThermaGraph-D™ is a white-mineral-oil-based fluid for single-phase immersion, with 0.05–0.20 wt% graphene in the supplied fluid. It is a different formulation from water-loop ThermaGraph; the water product’s internal +6–18% result must not be transferred to this fluid.
Compare heat removal, viscosity, pressure drop and total cooling electricity at a matched IT load. Before energizing equipment, obtain the lot’s electrical test results and the equipment supplier’s compatibility requirements; check elastomers, cables, soldermask and filtration. A formulation intended for dielectric service is not a blanket safety approval for every tank.
The DOE system-metering example supports evaluating the entire cooling chain, not just a fluid property. Potential resource benefits should be demonstrated through measured energy, fluid service requirements and maintenance, with fluid production, carrier, transport and end-of-life included in a consistent assessment.
Research / measurement reference · Continue with the application guide
Frequently asked questions
Can I put live boards in it right away?
Only once the lot's breakdown voltage and conductivity are on the signed technical data sheet. Do not energize boards before then.
Does it work in two-phase systems?
No. ThermaGraph-D™ is for single-phase immersion only.
What heat transfer improvement does it give?
We report heat transfer against the unfilled dielectric on each signed lab sheet, rather than a general figure. A 30-day sample in your tank gives you your own data.
Is it for HVAC?
No. ThermaGraph-D™ is a data center immersion fluid. For closed water loops, including HVAC chilled-water and hydronic loops, see ThermaGraph™.
How do I buy it?
ThermaGraph-D™ is quote-only for now. Request a quote or a 30-day sample and we will size the order to your tank.
More in Data Center & HVAC Coolants
-
ThermaGraph™ Data Center & HVAC Coolant
A ready-to-use graphene coolant in deionized water for closed-loop data center and HVAC cooling. A complete fill, not a top-off. View product -
Graphene Motor Oil Additive
A graphene additive for motor oils, supplied pre-mixed in an oil-based carrier so it blends straight into your oil. View product -
Graphene Gear Oil Additive
A graphene additive for gear oils, pre-mixed in an oil-based carrier for heavily loaded gear contacts. View product -
Graphene Hydraulic Fluid Additive
A graphene additive for hydraulic fluids, pre-mixed in an oil-based carrier for pumps, valves and cylinders. View product -
Graphene Grease Additive
A graphene additive for greases, pre-mixed in an oil-based carrier for blending into bearing and industrial greases. View product -
Graphene Coolant Additive
A graphene additive for liquid cooling loops, supplied pre-mixed in a water-based carrier. View product




