Data center cooling equipment representing graphene coolants and heat transfer

Graphene conducts heat along its sheet extremely well, so small amounts dispersed in a fluid, coating or polymer can create pathways that move heat more effectively than the base material alone. How much improvement you get depends on how well the graphene is dispersed, how much is added, and how heat actually moves in your system, so the effect has to be measured in your own application.

This guide explains the mechanism, the practical limits and how Graphene Integrations' coolants fit in.

Why does graphene conduct heat so well?

Heat in graphene is carried mainly by lattice vibrations moving through its tightly bonded carbon sheet. Within the plane of the sheet, graphene is one of the best thermal conductors known. Across the sheet, and between stacked sheets or the surrounding material, heat moves much less easily. That difference shapes how graphene behaves in real products. Read what is graphene for more background.

How does graphene improve heat transfer in a coolant?

In a liquid coolant, heat moves from a hot surface into the fluid and is carried away by flow. Dispersed graphene can change the fluid's thermal behavior and the heat exchange at the surface. Engineers usually describe this with the convective heat transfer coefficient, which combines fluid properties and flow.

Our ThermaGraph™ coolant is graphene in deionized water, supplied ready to use as a complete fill for closed loops, with 0.5–1.5 wt% graphene stated on the COA. It showed a +6% to +18% higher convective heat transfer coefficient than a glycol baseline in internal pumped-loop tests (internal testing results). Those are our own lab results, not independent field validation, and not an equivalent electricity saving. See data center coolants.

How does graphene help in polymers and coatings?

Most polymers are poor heat conductors. Graphene sheets that touch or nearly touch can form a network that spreads heat through a part or coating. The network only forms when the graphene is well dispersed and the loading is high enough. Poor dispersion leaves isolated clumps that do little. Our plastic additive and paint additive are supplied pre-dispersed in a resin or carrier matched to your system, so the starting point is a uniform mix.

What limits the improvement?

  • Interfaces. Heat has to cross from the matrix into each sheet and back, and each interface adds resistance.
  • Dispersion. Clumped or settled graphene does not form useful pathways.
  • Loading and viscosity. More graphene can help, but it also changes viscosity and processing.
  • System design. In a cooling loop, pump flow, heat exchanger design and fouling may matter more than the fluid.

How should I measure heat transfer improvement?

Compare the treated material with your current one under the same conditions. For fluids, log flow, inlet and outlet temperatures, pressure drop and heat load. For solids, use a recognized thermal conductivity method on matched specimens. Our guide on measuring heat transfer in a liquid cooling trial gives a step-by-step plan.

Where is graphene heat transfer being used?

  • Data centers: closed-loop direct-to-chip, CDU and rear-door heat exchanger loops with ThermaGraph, and single-phase immersion with ThermaGraph-D™, graphene in white mineral oil.
  • HVAC: closed chilled-water and hydronic loops where freeze protection is not required; see graphene nanofluids in HVAC.
  • Process and engine cooling: our coolant additive for water-based loops.
  • Electronics and batteries: research into heat spreading; see graphene in energy storage.

Frequently asked questions

Does adding more graphene always improve heat transfer?

No. Beyond a point, viscosity and pumping or processing effects can offset the gains. Test several loadings.

Is ThermaGraph a dielectric fluid?

No. ThermaGraph is water-based and must never immerse live electronics. ThermaGraph-D is the white-mineral-oil fluid for single-phase immersion.

Does ThermaGraph provide freeze protection?

No. It contains no glycol or freeze package and has a freeze point of 0 °C (32 °F). For loops that need freeze protection, a glycol build can be made on request.

Are the +6% to +18% results independent?

No. They are internal testing results from our own pumped-loop tests.

Request a quote, samples or a spec sheet

Tell us your material, the property you want to improve, the carrier you use (water, solvent, resin or oil) and your volumes. Pricing and samples are by quote. Call 704-659-3682 or request a quote, samples or a spec sheet / SDS.