Data center liquid cooling moves heat from servers into a liquid instead of relying only on air. The main approaches are direct-to-chip cooling, where coolant flows through cold plates on processors; rear-door heat exchangers, where a liquid-cooled coil sits on the back of a rack; and immersion cooling, where servers sit in a dielectric fluid. A coolant distribution unit (CDU) usually separates the server-side loop from the building's water system.
The terms below come up in nearly every liquid cooling project, from AI clusters to retrofits.
What is a CDU?
A coolant distribution unit is the equipment that circulates coolant to the racks and transfers heat to the facility water system through a heat exchanger. It controls flow, pressure and temperature on the server side, and keeps the technology cooling loop separate from facility water. CDUs can be in-row, in-rack or in a central plant.
What are the facility loop and the technology cooling loop?
- Facility water system (FWS): the building's water loop that carries heat to chillers, cooling towers or dry coolers.
- Technology cooling system (TCS): the closed loop between the CDU and the servers' cold plates or rear-door coils. Its fluid quality and compatibility matter most because it reaches the IT equipment.
What is direct-to-chip cooling?
Direct-to-chip (or direct liquid cooling) uses cold plates mounted on processors and other hot components. Coolant flows through the plates, picking up heat at the source. It is common for high-density AI and HPC servers. Coolants are typically water-based, such as treated water or propylene glycol mixes like PG25. Our PG25 alternative guide explains when a water-based graphene coolant fits.
What is a rear-door heat exchanger?
A rear-door heat exchanger is a liquid-cooled coil on the back of a rack. Hot exhaust air passes through it and is cooled before re-entering the room. It allows higher rack densities without changing the servers themselves.
What is immersion cooling?
In single-phase immersion, servers sit in a tank of dielectric liquid that stays liquid; it is pumped through a heat exchanger. In two-phase immersion, the fluid boils at the component surface and condenses on a coil. Immersion fluids must be dielectric. Our single-phase immersion fluid checklist covers selection.
What does "dielectric" mean?
A dielectric fluid does not conduct electricity in normal use, so it can contact live electronics. Water-based coolants are not dielectric and must stay inside sealed loops and cold plates. ThermaGraph-D™ is a graphene-enhanced dielectric fluid in white mineral oil for single-phase immersion. ThermaGraph™, graphene in deionized water, is not a dielectric and must never immerse live electronics.
What is the convective heat transfer coefficient?
It is a measure of how effectively heat moves between a surface and a flowing fluid. A higher value means more heat moved for the same temperature difference. In internal pumped-loop tests, ThermaGraph showed a +6% to +18% higher convective heat transfer coefficient than a glycol baseline (internal testing results). See how to measure heat transfer in a cooling trial.
What is PUE?
Power usage effectiveness is total facility energy divided by IT equipment energy. A lower PUE means less overhead for cooling and power distribution. Cooling improvements can affect PUE, but only measured energy shows by how much.
What do freeze protection and glycol mean here?
Glycol is added to water to lower its freeze point, at some cost to heat transfer. Indoor loops that never see freezing conditions may not need it. ThermaGraph contains no glycol and no freeze package, with a freeze point of 0 °C (32 °F), so it is intended for loops where freeze protection is not required. If a loop needs freeze protection, we can make a glycol build on request.
Where can I learn more?
See data center coolants, the data centers industry page, graphene coolants for AI data centers and ThermaGraph vs ThermaGraph-D.
Frequently asked questions
Is direct-to-chip cooling the same as immersion cooling?
No. Direct-to-chip keeps coolant inside cold plates; immersion places servers in a dielectric fluid.
Do CDUs need a special coolant?
The technology cooling loop needs a fluid compatible with its materials and the server manufacturer's requirements. Check before changing fluids.
Can ThermaGraph be used in an immersion tank?
No. Use ThermaGraph-D, the white-mineral-oil fluid, for single-phase immersion.
Is ThermaGraph a top-off additive?
No. It is a complete fill.
Request a quote, samples or a spec sheet
Tell us your material, the property you want to improve, the carrier you use (water, solvent, resin or oil) and your volumes. Pricing and samples are by quote. Call 704-659-3682 or request a quote, samples or a spec sheet / SDS.
