A graphene concrete additive and concrete fibers solve different problems. Fibers, whether steel, synthetic or glass, are added to control cracking and improve toughness after the concrete cracks; a graphene additive works within the cement paste and is evaluated for properties such as compressive strength. Our graphene concrete additive gave +67.7% compressive strength at 5% by weight of cement in independent third-party testing (2023), which is a different measure from the post-crack performance fibers are chosen for.
Because they target different properties, the question is usually not "which one" but "which problem are we solving", and sometimes both are tested together.
What do fibers do in concrete?
- Synthetic microfibers (for example polypropylene) are commonly used to reduce plastic shrinkage cracking in fresh concrete.
- Synthetic macrofibers and steel fibers are used to provide residual strength and toughness after cracking, and in some designs to replace part of the conventional reinforcement for certain slabs.
- Glass fibers are used in glass-fiber-reinforced concrete products such as thin panels.
Fibers are typically specified and tested using flexural and toughness tests, as well as the producer's and engineer's requirements.
What does a graphene additive do in concrete?
Graphene is dispersed through the cement paste rather than acting as discrete reinforcing strands. Our additive, NanoTechCrete, is a water-compatible graphene concentrate, validated at 5% by weight of cement (loading depends on mix design; see TDS). Its published result is a compressive-strength gain in independent third-party testing. See the graphene concrete additive page and how graphene concrete additive works.
How are they dosed differently?
Fibers are usually dosed by weight or volume per cubic yard or cubic meter of concrete. Our graphene additive is dosed by weight of cement: the 5% refers to supplied additive mass relative to cement mass, not total concrete mass and not pure graphene. Because the additive brings water with it, adjust the batch water; see graphene concrete mix design and the mixing instructions.
How should each be tested?
- Compressive strength: cylinders tested under a recognized method such as ASTM C39, at the test ages your project requires.
- Post-crack toughness and flexural performance: beam or panel tests used for fiber-reinforced concrete.
- Fresh properties: slump or workability, air content and finishing behavior for both.
- Durability: exposure-specific tests the engineer requires.
Test against a documented control mix made with the same materials. Our guide to validating graphene concrete explains how to set up the comparison.
Can graphene and fibers be used together?
They can be tested together, since they act at different scales. If you are considering both, run a control, a graphene-only mix, a fiber-only mix and a combined mix, and measure the properties each is meant to affect. We do not publish data for combined systems, so any combination needs its own testing.
Does stronger concrete mean less cement or lower carbon?
A strength gain supports investigating lower-cement mixes, but it does not by itself establish how much cement can be removed or a carbon saving. Candidate mixes must meet the same required performance, and a carbon comparison must include the additive's own impacts. See concrete and embodied carbon and why cement emits CO₂.
Where might each make sense?
Fibers are well established for slabs-on-ground, shotcrete, precast elements and crack control. Graphene concrete additive is being evaluated where compressive strength is the target; see where graphene concrete makes sense. Decisions belong to the producer and the project engineer.
Frequently asked questions
Does graphene replace steel rebar?
No. Our concrete additive is not a replacement for structural reinforcement. We are separately developing a graphene composite rebar, which is in development.
Does graphene stop concrete cracking?
We do not publish crack-control data for our additive. Fibers are the established tool for shrinkage and post-crack control.
What dose of graphene additive is used?
Our concrete additive is validated at 5% by weight of cement; loading depends on mix design, see the TDS.
Can I buy the concrete additive online?
See the concrete additive in our store. Pricing and samples are by quote.
Request a quote, samples or a spec sheet
Tell us your material, the property you want to improve, the carrier you use (water, solvent, resin or oil) and your volumes. Pricing and samples are by quote. Call 704-659-3682 or request a quote, samples or a spec sheet / SDS.
